Sidel SBO 30 heater tube spare

Sat, 27 Jun 2026 07:34:10 +0800

On a PET line, the heating tunnel is where the schedule gets made—or broken. When the Sidel SBO 30 is running, preform temperature has to stay inside the recipe band, ±1°C across the preform wall. If it drifts, stretch gets unstable. You start seeing thick heels, thin shoulders, and bottles that just miss the spec. A weak or aging emitter makes that obvious in a hurry—cycle time creeps, scrap climbs, and you get more alarms right at shift change. What matters, technically We build the SBO 30 heater tube as a short-wave infrared halogen emitter, matched to the machine’s heating-zone geometry and power map. The quartz envelope is cut to the standard SBO 30 length, and it uses an R7s connector so you can swap it without rewiring the block. We set the filament load and spectral output for fast response—heat-up in seconds, not minutes—so the tunnel can hold temperature when the line switches from 28mm to 38mm necks and back again. Every unit gets run-in and measured for consistent wattage and stable output across its life. Why it holds up in practice This tube is built for one job: keeping the SBO 30 consistent. It hits the preform heating curve the machine expects, so stretch ratios stay repeatable and bottle weight stays in control. That means fewer tiny tweaks, less scrap during changeovers, and more uptime between lamp changes. Energy use stays predictable because the emitter puts the heat where it’s needed, with less waste bleeding into the tunnel air path. Here’s what to keep in mind Compatibility is straightforward, but it’s not universal. This tube is a direct fit for the Sidel SBO 30 blow molder and also works on major platform lines—Sidel Matrix, Krones Contiform, and Husky HyPET—as long as the holder, connector, and zone power match the OEM setup. Install it only when the tunnel is at ambient temperature and the zone is powered off. If it’s misaligned or touching reflectors, lamp life will take a hit. For the best result, pair the replacement with a clean reflector and verify zone temperature using the machine’s own sensors after startup.

Nissei ASB 70DP/150DP infrared lamp spare

Mon, 01 Jun 2026 23:25:06 +0800

When the heating tunnel on your Nissei ASB 70DP or 150DP starts drifting, you don’t have time to play guessing games with parts. Output dips, preforms scorch or come up short, and the line starts chasing scrap instead of cycle time. We built our infrared lamp spares as direct, engineered replacements for these machines so you can swap in, retune once, and get back to stable production. What matters is repeatable heat right where the ASB process is sensitive: the preform heating zone. Our lamps are short-wave infrared, quartz envelope, with a matched R7s connector—sized to the OEM footprint and wattage. You get the same thermal response and temperature profile as the original, so the heating curve doesn’t shift when you change lamps. We specify voltage and power to match the machine’s heating section, and the filament geometry is tuned for even coverage across the preform wall, cutting hot spots that lead to crystallization and weak blows. And here’s the payoff: it keeps your stretch blow molding cycle consistent. With matched infrared output, preform reheat is repeatable shot to shot, so you see fewer rejects from inconsistent stretch and wall thickness. Energy use stays flat because the lamp hits setpoint quickly and holds it without overshoot. In the real world, teams running these spares report fewer heating-related stops, and lamp changeovers take minutes, not hours. One thing to remember up front: these lamps run hot, and the heating tunnel is tight.**Handle them by the base only.**Keep the quartz clean, and check the reflector condition before install—worn reflectors can throw off the heat profile even with a new lamp. Match the voltage and connector, and you’ll get the performance the ASB 70DP/150DP was designed for.

Spare on Quartz IR Heating Bulbs

Sidel SBO 30 heater tube spare

Nissei ASB 70DP/150DP infrared lamp spare